Free delivery on the 10-pack

Bag 0

Motorola · tempered glass · cut for one phone

Motorola Edge 60 Pro Super X Clear tempered glass

6.7" · Centre punch-hole · Curved edge · 0.33mm · 9H

This glass is cut for the Motorola Edge 60 Pro only. Have the Motorola Edge 60? It needs its own cut — Motorola Edge 60 tempered glass →

₹999 MRP ₹3,330 70% off

₹100 each · 10-pack

Shops sell one screen guard for up to ₹799. We sell direct, so yours costs ₹100 a sheet — same 9H glass, no middleman.

Inclusive of all taxes. ₹50 delivery — free with the 10-pack.

Finish
Pack size

Order before 4 PM IST — dispatched today from Bengaluru.

₹250 nowPartial COD, rest at the door 7 daysReturns on unused glass Chipped?A photo gets a new sheet

Glass only — no alignment frame or cleaning kit in the pack.

10 × tempered glass · phone not included · TG-MOT-MOTOROLAEDGE60PRO-REG-10

Add a Motorola Edge 60 Pro skinBack + front · Matte or Clear · ships together New →

What fits

Why this fits your Motorola Edge 60 Pro

Display
6.7"
Edge
Curved edge
Cutout
Centre punch-hole
Unlock
Optical in-display reader
Thickness
0.33mm

The Motorola Edge 60 Pro’s 6.7-inch display curves away at the sides. Rigid glass cannot follow the bend, so the sheet stops just inside it and is bonded across its whole surface — expect a slim border at the edges; that is what stops it lifting. The centred punch-hole camera sits under clear glass with nothing printed over it, so selfies and video calls look the same. The optical fingerprint reader under the display works through 0.33mm glass; re-register your finger after fitting.

Not interchangeable with the Motorola Edge 60 Stylus: the Motorola Edge 60 Pro has a curved edge and the Motorola Edge 60 Stylus does not.

In every pack

10×

Tempered glass sheets, cut for the Motorola Edge 60 Pro

Glass only. There is no alignment frame, cleaning pad or dust sticker in the pack, and the phone is not included.

Fitting it

Four steps, ten minutes

The full guide, with pictures →
  1. 01

    Clean the screen with a lint-free cloth, then lift any dust left with a strip of clear tape — a single speck is what causes a permanent bubble.

  2. 02

    Peel the backing and hold the sheet by its edges over the Motorola Edge 60 Pro. Line up the cut-outs at the top first, then the sides.

  3. 03

    Lower the glass onto the centre of the panel and let go. The adhesive pulls itself outward from the middle.

  4. 04

    Press any remaining edge gently toward the border. Small perimeter bubbles clear on their own within 24 hours.

Questions about the Motorola Edge 60 Pro

Will tempered glass slow down the Motorola Edge 60 Pro’s fingerprint reader?

No. The Motorola Edge 60 Pro reads your finger optically through the display, and at 0.33mm with full-surface adhesive there is no air gap for the light to scatter in. Delete and re-register your fingerprint after fitting — the sensor calibrates to what it reads through.

Will a Motorola Edge 60 Stylus protector fit the Motorola Edge 60 Pro?

No. The Motorola Edge 60 Pro has a curved edge and the Motorola Edge 60 Stylus does not — a cut for one will not sit right on the other.

Why doesn’t the glass reach the very edge of the Motorola Edge 60 Pro’s screen?

Because the edge curves. Tempered glass is rigid, and a sheet cut to wrap the bend lifts, traps air and shows a rainbow halo. Stopping just inside the curve keeps the whole sheet bonded; the thin border that leaves is deliberate.

What happens if one arrives damaged?

Check the pack when it arrives. A sheet that is chipped, cracked or cut for the wrong model is replaced — send us a photo and we ship a new one. You do not need to send the damaged sheet back.

How much is delivery, and how do I pay?

Delivery is ₹50 on the 3-pack and the 5-pack, free on the 10-pack. Pay in full online — UPI, cards, netbanking — or Partial COD, which costs nothing extra: a ₹250 booking fee online to confirm, and the rest in cash at the door. Orders placed before 4 PM IST are dispatched the same day.

Is it full glue or UV glass?

Full glue, not UV. The adhesive covers the whole sheet rather than a frame round the edge, so there is no air gap over the display or an in-display reader — and it is already on the glass: peel, line up, press. No liquid glue and no UV lamp.

Will it fit inside my case?

Yes. We cut to the active display area rather than the full front face, which leaves the case lip clear on every model we support. A protector cut edge-to-edge is the one that fights a case.

More on delivery, payment, returns and bulk orders: all questions →

More in the Edge 60

Before and after